The post Tektronix MDO3024 200 MHz Mixed Signal Oscilloscope appeared first on Global Test Equipment.

The post Keysight MSOX3054A Mixed Signal Oscilloscope: 500 MHz, 4 Analog Plus 16 Digital Channels appeared first on Global Test Equipment.

Channels: 2
Sensitivity: 5 mV to 50 V/div (to 500 V/div with 10X probe)
Record Length: 2500 points
Video Triggering Formats and Field Rates: Odd field, even field and line
Waveform Processing: Add, Subtract, Multiply, Calculate Watts = V x I
Waveform Storage: 10 waveforms
Cursor Measurements: ΔVolts, ΔTime, 1/ΔTime (Hz), Degree (phase)
Cursor Types: Horizontal Bars, Vertical Bars, Paired (volts @ time)

Tektronix THS730A Automatic Measurements:Period; +Width; -Width; +Duty Cycle; -Duty Cycle; High; Low; Peak-to-Peak; Mean; Cycle Mean; Burst Width; Frequency; Rise Time; Fall Time; +Overshoot; -Overshoot; Max; Min; Amplitude; RMS; Cycle RMS
Tektronix THS730A DMM Specifications:

DC Voltage Ranges: 400.0 mV to 880 V
True RMS AC Voltage Ranges: 400.0 mV to 640 V
Resolution: 4000 count, 3-3/4 digits
Resistance Ranges: 400.0 ohm to 40.00 Mohm
Diode Test Range: 0 to 2 volts
Continuity Check: Audible tone when < 50 ohm
Modes: Min, Max, Δ-Max-Min, Avg, Hold
Non-Volatile Storage: 10 DMM screenshots

The post Tektronix THS730A 200 Mhz 1Gs/S Oscilloscope and Meter appeared first on Global Test Equipment.

500 MHz
2 input channels
1 Megohm/50 Ohm inputs
2 mV to 5V/div, 1 ns to 5 s/div
Ext trigger w/trigger view
Probe multiplier readout
20 MSa/s max sampling rate
4k max record length, 2k single shot
100 ps timebase resolution
8-bit vertical resolution
1,500,000 points/s update rate
Cursors
Save/recall 10 panel setups
14 automatic measurements
GPIB, RS-232, hard copy, FFT, extended waveform math & more with optional modules

The post Keysight 54610B 20 MSa/s 500 MHz 2 Channel Oscilloscope appeared first on Global Test Equipment.

When both the RF channel and any analog or digital channels are on, the oscilloscope display is split into two views. The upper half of the display is a traditional oscilloscope view of the Time Domain. The lower half of the display is a Frequency Domain view of the RF input. Note that the Frequency Domain view is not simply an FFT of the analog or digital channels in the instrument, but is the spectrum acquired from the RF input.

The spectrum shown in the Frequency Domain view is taken from the period of time indicated by the short orange bar in the time domain view – known as the Spectrum Time. With the MDO4000 Series, Spectrum Time can be moved through the acquisition to investigate how the RF spectrum changes over time. And this can be done while the oscilloscope is live and running or on a stopped acquisition.

The time domain graticule on the MDO4000 Series display provides support for three RF time domain traces that are derived from the underlying I and Q data of the RF input including:

Amplitude – The instantaneous amplitude of the RF input vs. time
Frequency – The instantaneous frequency of the RF input, relative to the center frequency vs. time
Phase – The instantaneous phase of the RF input, relative to the center frequency vs. time

Each of these traces may be turned on and off independently, and all three may be displayed simultaneously. RF time domain traces make it easy to understand what’s happening with a time-varying RF signal.

The post Tektronix MDO4054-6 Mixed Domain Oscilloscope, 4+16 Channel, 500 MHz with 6 GHz Spectrum Analysis appeared first on Global Test Equipment.

When both the RF channel and any analog or digital channels are on, the oscilloscope display is split into two views. The upper half of the display is a traditional oscilloscope view of the Time Domain. The lower half of the display is a Frequency Domain view of the RF input. Note that the Frequency Domain view is not simply an FFT of the analog or digital channels in the instrument, but is the spectrum acquired from the RF input.

The spectrum shown in the Frequency Domain view is taken from the period of time indicated by the short orange bar in the time domain view – known as the Spectrum Time. With the MDO4000 Series, Spectrum Time can be moved through the acquisition to investigate how the RF spectrum changes over time. And this can be done while the oscilloscope is live and running or on a stopped acquisition.

The time domain graticule on the MDO4000 Series display provides support for three RF time domain traces that are derived from the underlying I and Q data of the RF input including:

Amplitude – The instantaneous amplitude of the RF input vs. time
Frequency – The instantaneous frequency of the RF input, relative to the center frequency vs. time
Phase – The instantaneous phase of the RF input, relative to the center frequency vs. time

Each of these traces may be turned on and off independently, and all three may be displayed simultaneously. RF time domain traces make it easy to understand what’s happening with a time-varying RF signal.

The post Tektronix MDO4104-6 Mixed Domain Oscilloscope, 4+16 Channel, 1 GHz with 6 GHz Spectrum Analysis appeared first on Global Test Equipment.

When both the RF channel and any analog or digital channels are on, the oscilloscope display is split into two views. The upper half of the display is a traditional oscilloscope view of the Time Domain. The lower half of the display is a Frequency Domain view of the RF input. Note that the Frequency Domain view is not simply an FFT of the analog or digital channels in the instrument, but is the spectrum acquired from the RF input.

The spectrum shown in the Frequency Domain view is taken from the period of time indicated by the short orange bar in the time domain view – known as the Spectrum Time. With the MDO4000 Series, Spectrum Time can be moved through the acquisition to investigate how the RF spectrum changes over time. And this can be done while the oscilloscope is live and running or on a stopped acquisition.

The time domain graticule on the MDO4000 Series display provides support for three RF time domain traces that are derived from the underlying I and Q data of the RF input including:

Amplitude – The instantaneous amplitude of the RF input vs. time
Frequency – The instantaneous frequency of the RF input, relative to the center frequency vs. time
Phase – The instantaneous phase of the RF input, relative to the center frequency vs. time

Each of these traces may be turned on and off independently, and all three may be displayed simultaneously. RF time domain traces make it easy to understand what’s happening with a time-varying RF signal.

The post Tektronix MDO4054-3 Mixed Domain Oscilloscope, 4+16 Channel, 500 MHz with 3 GHz Spectrum Analysis appeared first on Global Test Equipment.

When both the RF channel and any analog or digital channels are on, the oscilloscope display is split into two views. The upper half of the display is a traditional oscilloscope view of the Time Domain. The lower half of the display is a Frequency Domain view of the RF input. Note that the Frequency Domain view is not simply an FFT of the analog or digital channels in the instrument, but is the spectrum acquired from the RF input.

The spectrum shown in the Frequency Domain view is taken from the period of time indicated by the short orange bar in the time domain view – known as the Spectrum Time. With the MDO4000 Series, Spectrum Time can be moved through the acquisition to investigate how the RF spectrum changes over time. And this can be done while the oscilloscope is live and running or on a stopped acquisition.

The time domain graticule on the MDO4000 Series display provides support for three RF time domain traces that are derived from the underlying I and Q data of the RF input including:

Amplitude – The instantaneous amplitude of the RF input vs. time
Frequency – The instantaneous frequency of the RF input, relative to the center frequency vs. time
Phase – The instantaneous phase of the RF input, relative to the center frequency vs. time

Each of these traces may be turned on and off independently, and all three may be displayed simultaneously. RF time domain traces make it easy to understand what’s happening with a time-varying RF signal.

The post Tektronix MDO4104-3 Mixed Domain Oscilloscope, 4+16 Channel, 1 GHz with 3 GHz Spectrum Analysis appeared first on Global Test Equipment.