Com-Power - Global Test Equipment https://4gte.com/brand/com-power/ Service, Solutions, Satisfaction Sat, 13 Sep 2025 00:00:06 +0000 en-US hourly 1 https://wordpress.org/?v=6.8.2 https://4gte.com/wp-content/uploads/2025/05/logowithouttext-resized-250-x-250-100x100.gif Com-Power - Global Test Equipment https://4gte.com/brand/com-power/ 32 32 Com-Power LI-215A Line Impedance Stabilization Network https://4gte.com/products/com-power-li-215a-line-impedance-stabilization-network/ Fri, 17 May 2024 14:39:39 +0000 https://4gte.com/?post_type=product&p=65980 Com-Power LI-215A Line Impedance Stabilization Network

The post Com-Power LI-215A Line Impedance Stabilization Network appeared first on Global Test Equipment.

]]> Com-Power LI-215A Line Impedance Stabilization Network

The post Com-Power LI-215A Line Impedance Stabilization Network appeared first on Global Test Equipment.

]]> Com-Power CLCI-100 Bulk Current Injection Probe, 10 kHz to 100 MHz, 100 Watts (CW) https://4gte.com/products/com-power-clci-100/ Wed, 08 May 2024 18:34:35 +0000 https://4gte.com/?post_type=product&p=65810 Com-Power CLCI-100 Bulk Current Injection Probe, 10 kHz to 100 MHz, 100 Watts (CW)

The post Com-Power CLCI-100 Bulk Current Injection Probe, 10 kHz to 100 MHz, 100 Watts (CW) appeared first on Global Test Equipment.

]]> Com-Power CLCI-100 Bulk Current Injection Probe, 10 kHz to 100 MHz, 100 Watts (CW)

The CLCI-100 incorporates split-core ferrites into its rugged, circular enclosure, and is hinged; thereby allowing the probe to be opened on one side in order to easily place the wire, cable(s) or cable bundle(s) to be tested into the probe window, making the CLCI-100 much more convenient to use than other non-split core probes.

The post Com-Power CLCI-100 Bulk Current Injection Probe, 10 kHz to 100 MHz, 100 Watts (CW) appeared first on Global Test Equipment.

]]> Com-Power CG-520 Comb Generator, 20 MHz – 4.5 GHz, 20 MHz step https://4gte.com/products/com-power-cg-520-comb-generator-20-mhz-4-5-ghz-20-mhz-step/ Tue, 17 Feb 2015 17:31:47 +0000 http://globaltest.wpengine.com/?post_type=product&p=37666 The CG-500 Series Comb Generators are reference signal
sources providing frequency harmonics at preset frequency
intervals. The output signal of the Comb Generator is used
as a conducted or a radiated signal source.
As a conducted signal source, the output is available
directly from the connector. Two antennas are supplied
with the Comb Generator for generating radiated reference
signals.
The Comb Generator is powered by a rechargeable internal
battery. Battery power eliminates any possible measurement
variations that can be caused by an external power
cable connection. When fully charged, the battery allows
continuous operation for up to 18 hours. Internal control
and monitoring circuits provide indications of valid output
signals

The post Com-Power CG-520 Comb Generator, 20 MHz – 4.5 GHz, 20 MHz step appeared first on Global Test Equipment.

]]> The most important application of a Comb Generator,
is trouble shooting Open Area Test Sites (OATS). An
OATS must be completely calibrated before it is put into
service. When the validity of the test data taken at an
OATS is in doubt after it is put into service, it is not
always practical to perform complete site calibration.
The Comb Generator is a quick calibration tool that can
help identify potential problems with the site. For instance,
emission measurements taken from a product at
two different test sites can sometimes vary. It is very
difficult to determine the cause of the variation. Using
the same test setup, measurement can be taken with a
Comb Generator in place of the product at both sites. The
data can be compared to determine if variation is due to
the product or the test site.

The post Com-Power CG-520 Comb Generator, 20 MHz – 4.5 GHz, 20 MHz step appeared first on Global Test Equipment.

]]> Com-Power LI-125 150KHz – 30 MHz Line Impedance Stabilization Network https://4gte.com/products/com-power-li-125-150khz-30-mhz-line-impedance-stabilization-network/ Fri, 17 Jan 2014 15:05:42 +0000 http://globaltest.wpengine.com/?post_type=product&p=36486 Com-Power LI-125 150KHz - 30 MHz Line Impedance Stabilization Network.  30 MHz, 25A, 270 VAC & 380 VDC

The post Com-Power LI-125 150KHz – 30 MHz Line Impedance Stabilization Network appeared first on Global Test Equipment.

]]> Frequency: 150 kHz – 30 MHz
Application: FCC Part 15, CISPR 22, EN 55022
Max Current (Amp): 25 A
Voltage: 115/ 270 VAC, 380 VDC
Inductor: 50 µH
Inductor type: Air Core
Number of lines: 2
Output impedance: 50Ω
Output Connector: N type (f)
Power source frequency: DC-60 Hz

The post Com-Power LI-125 150KHz – 30 MHz Line Impedance Stabilization Network appeared first on Global Test Equipment.

]]>